Home | Classifieds | History | Technical | Links | Store | About Us | Email
Topics Topics Edit Profile Profile Help/Instructions Help Member List Register  
Search Last 1|3|7 Days Search Search Tree View Tree View  

Making brass gas tanks

Old Marine Engine » Carburetors, Mixers, Vaporizors » Making brass gas tanks « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Richard Alcock
Advanced Member
Username: raa

Post Number: 40
Registered: 02-2007


Posted on Thursday, December 15, 2011 - 08:42 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

I thought I would pass along how I make my brass gas tanks. I get .020 half hard brass CA 260 sheared to size from Speedy Metals 262-784-4140 New Berlin Wi. The die formed ends are cut in circles and placed in the recess on the female die and the male part is shoved through forming the end with very little blemishes. I grease both halves of the die prior to forming. I use a compound arbor press with no problem. The ends are 5.330" dia. and the tank can be any length. I have .003" clearance between the male and female die. Prior to forming I use a torch and heat the blanks to a dull red and quench in water so they are real soft.
I also made a loose pattern to cast the tank supports which can be used on most engines.

gas tank tooling 1

gas tank tooling 2



gas tank tooling 4
Top of pagePrevious messageNext messageBottom of page Link to this message

Jim Parrott
Advanced Member
Username: jim_parrott

Post Number: 36
Registered: 06-2009
Posted on Friday, December 16, 2011 - 04:08 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Dick,

That is some good looking stuff. Do you get the tank as a tube or do you roll it? I always wanted to build some tanks and rivit them together.

Jim
Top of pagePrevious messageNext messageBottom of page Link to this message

Harold (Hal) Houghton
New member
Username: hal1

Post Number: 2
Registered: 12-2010
Posted on Friday, December 16, 2011 - 04:53 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Hello Dick;

Can you tell me where you get the dies made? I am receiving many requests to reproduce the old vacuum tank floats.

Thank you.

Hal Houghton
The Classic Preservation Coalition
Top of pagePrevious messageNext messageBottom of page Link to this message

Richard Alcock
Advanced Member
Username: raa

Post Number: 41
Registered: 02-2007


Posted on Friday, December 16, 2011 - 10:14 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

I get the brass cut to the size I need from Speedy Metal. I use hose clamps to hold the parts together and I fine scotch brite all the surfaces where I intend to solder. I use a paste to help the solder stick and I use Mc Master-Carr # 7656A4 high strength solder. After soldering I use a 6"x 12" scotch brite wheel to remove all excess solder and to generally clean the tank up. After the tank is partly soldered I drill a small hole where the drain and fill will be which lets the tank vent itself as I finish the soldering. After soldering I use a step drill to open the holes to what I need for the drain and fill parts.
Top of pagePrevious messageNext messageBottom of page Link to this message

Richard Alcock
Advanced Member
Username: raa

Post Number: 42
Registered: 02-2007


Posted on Friday, December 16, 2011 - 10:20 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

I made the female die myself and I had a friend spin the male part out on a CNC lathe. The clearance between the male and female die part is .040 plus .003"
application/pdfmale die drawing
RAA1.pdf (6.5 k)
Top of pagePrevious messageNext messageBottom of page Link to this message

Harold (Hal) Houghton
New member
Username: hal1

Post Number: 3
Registered: 12-2010
Posted on Friday, December 16, 2011 - 05:07 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Hello Dick;

Thanks for the response. Are you and your friends interested in making some dies for me?
Top of pagePrevious messageNext messageBottom of page Link to this message

Keith kinney
Member
Username: kkinney

Post Number: 10
Registered: 04-2011
Posted on Friday, December 16, 2011 - 06:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Beautiful work and tanks! I'd be interested in a set of dies too if anybody makes some. Richard, any chance you could make a YouTube video actually showing the process. I'm don't really fully understand how the dies work. What do you do for the filler and fuel line fittings. Thank you for posting.
Keith
www.herculesengines.com
Top of pagePrevious messageNext messageBottom of page Link to this message

J.B. Castagnos
Senior Member
Username: jb_castagnos

Post Number: 637
Registered: 07-2002


Posted on Friday, December 16, 2011 - 07:20 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

They look great Dick. I read about a jig to make radius cuts, haven't tried it yet. It sounds like it should work and it's fairly simple. You make a pointed tool, like a pencil sharpened on both ends, you need a dimple in the cross feed, and a stop on the carriage with a dimple. The pointed tool sits between these dimples, parallel to the bed, the length of the tool will determine the radius of the cut. If you bring the carriage against the pointed tool and hold it there with the hand wheel, as you feed out the tool will start to angle, this will give you the radius. The compound has to be set at a 90, this allows you to feed in for each cut. The rod on the chuck side of the carriage will give a convex cut, on the tailstock side will give a concave cut. A threaded telescoping rod would allow to make one radius .030" smaller than the other.
Top of pagePrevious messageNext messageBottom of page Link to this message

Andrew Selman
Member
Username: andys

Post Number: 13
Registered: 05-2007
Posted on Saturday, December 17, 2011 - 09:03 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Hello Dick,

That looks like great work!

I have a couple of questions :-
How much bigger is the original disc than the final diameter and does it just pull it in, smoothly without any wrinkles?
Did you find that the radius between the end dich and the side was critical, or did it just work?

Thanks
Andy
Top of pagePrevious messageNext messageBottom of page Link to this message

Richard Alcock
Advanced Member
Username: raa

Post Number: 43
Registered: 02-2007


Posted on Saturday, December 17, 2011 - 03:04 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

This is a hand sketch of the tank parts. The original brass disk is .80 approx larger than the male die. I see small wrinkles as the die starts to form but they all get smoothed out since there is only about .003 clearance. The radius is/was just a guess(happy accident). I will do two more ends next week and post a few more pictures to help clear things up. The annealed blanks simply lay in the recess on the top of the female die. This recess is about .125" deep and is about 6.25" in diameter. The blanks are about 6.125" in diameter. I noticed that I listed the scotchbrite wheel dimensions wrong should be 6"x 1" running at 3450 rpm
Tank part drawing
Top of pagePrevious messageNext messageBottom of page Link to this message

Keith kinney
Member
Username: kkinney

Post Number: 11
Registered: 04-2011
Posted on Saturday, December 17, 2011 - 03:17 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

So there are just two parts to the die, the outer ring and the inner convex die? I was thinking you would have a 3rd concave bottom die but I guess the dish is formed by wrapping around the top die?
For the fittings you turn them yourself on a lathe?
Keith
www.herculesengines.com
Top of pagePrevious messageNext messageBottom of page Link to this message

Richard Alcock
Advanced Member
Username: raa

Post Number: 44
Registered: 02-2007


Posted on Saturday, December 17, 2011 - 05:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Yes I turn them on my lathe. The cap takes the most time but us old gezzeers got lots of time. Actually once you have all the tools and drills assembled it goes pretty quick. Since the threads are fine they cut in just a few passes. If you need just a few ends just get some material and cut them out and I will run them through for you.

cheers

Dick
Top of pagePrevious messageNext messageBottom of page Link to this message

Richard Alcock
Advanced Member
Username: raa

Post Number: 45
Registered: 02-2007


Posted on Monday, December 19, 2011 - 03:54 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

I ran a couple more tanks ends and took a few pictures to show the sequence better. I had a few more wrinkles which were hammered out easily with a plastic hammer. I also chucked up the tool and hand held a roller which smoothed out the little remaining marks.
tank 1
tank 2
tank 3
tank 4
tank 5
tank 6
tank 8
Top of pagePrevious messageNext messageBottom of page Link to this message

Paul Gray
Senior Member
Username: paulgray

Post Number: 107
Registered: 05-2003
Posted on Tuesday, December 20, 2011 - 07:01 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Rich- Thanks for posting those latest pictures. That really clarifies the process.
Top of pagePrevious messageNext messageBottom of page Link to this message

Keith kinney
Member
Username: kkinney

Post Number: 12
Registered: 04-2011
Posted on Tuesday, December 20, 2011 - 06:56 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Yes, thank you! That really helps to show how you did it.
Keith
Top of pagePrevious messageNext messageBottom of page Link to this message

William Schaller
Senior Member
Username: billschaller

Post Number: 459
Registered: 12-2003


Posted on Thursday, December 22, 2011 - 11:04 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Dick,

Can you show us how you make the tube? This very early Woolery seems to always leak.

Top of pagePrevious messageNext messageBottom of page Link to this message

William Ferraro
Visitor
Posted on Wednesday, April 01, 2015 - 11:33 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Bayfield Maritime Museum: We are in the process of restoring a Motorgo Row Boat Engine. We have no gas tank. Who would we contact to find or have one made?
Top of pagePrevious messageNext messageBottom of page Link to this message

J.B. Castagnos
Senior Member
Username: jb_castagnos

Post Number: 1046
Registered: 07-2002


Posted on Wednesday, April 01, 2015 - 05:00 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Sears sold motors under the Motorgo label, not familiar with the row boat motor, could be one of a number of manufaturers . Can you post a picture?
Top of pagePrevious messageNext messageBottom of page Link to this message

Richard Alcock
Senior Member
Username: raa

Post Number: 195
Registered: 02-2007


Posted on Friday, January 11, 2019 - 10:14 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Here are a few pictures of a simple rolling device which I made to roll up my gas tanks.









Top of pagePrevious messageNext messageBottom of page Link to this message

Ned Lloyd
Senior Member
Username: ned_l

Post Number: 185
Registered: 08-2012
Posted on Thursday, January 17, 2019 - 05:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Beautiful work!!!!
Top of pagePrevious messageNext messageBottom of page Link to this message

chris spring
Senior Member
Username: spring

Post Number: 60
Registered: 06-2018
Posted on Friday, January 18, 2019 - 08:26 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Nice!
Top of pagePrevious messageNext messageBottom of page Link to this message

Stef
Member
Username: ssilent11

Post Number: 9
Registered: 02-2007
Posted on Saturday, April 20, 2019 - 07:31 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

very pleasing to see fine work

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Automatically activate URLs in message
Action:

Administration Administration Log Out Log Out   Previous Page Previous Page Next Page Next Page

Home | Classifieds | History | Technical | Links | Store | About Us | Email
&copy 2005 OldMarineEngine.com, P.O. Box 188, Forest Dale, VT 05745-0188 • Phone: 802-247-4864 • All rights reserved.
   Marine Engine Seloc Repair Manual Lookup Tool

marine gas engine repair and restoration