Home | Classifieds | History | Technical | Links | Store | About Us | Email
Topics Topics Edit Profile Profile Help/Instructions Help Member List Register  
Search Last 1|3|7 Days Search Search Tree View Tree View  

Three Position Switch for P66(Start ....

Old Marine Engine » Stuart Turner » Three Position Switch for P66(Start .Stop .Charge) « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

dragonrider
New member
Username: dragonrider

Post Number: 1
Registered: 06-2005
Posted on Friday, June 17, 2005 - 03:35 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Required 3 position switch (Start, Stop,Charge)for P66.Tried Fairways, they do not do them anymore.Or advise on how to wire without 3 position switch. Also help required on cone clutch ajustment. Have to put into reverse before drive forward starts.Any help appreciated, thankyou.
Top of pagePrevious messageNext messageBottom of page Link to this message

timmulvey
Senior Member
Username: timmulvey

Post Number: 162
Registered: 05-2003


Posted on Saturday, June 18, 2005 - 05:36 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

I'll send you a 3 page article on the dynastart.
Top of pagePrevious messageNext messageBottom of page Link to this message

david_stott
New member
Username: david_stott

Post Number: 2
Registered: 06-2005
Posted on Sunday, June 19, 2005 - 09:36 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Dragonrider, you just need a start switch/button, and a stop button. I have wired these seperately.
I used push buttons from current marine chandelry's, and they work well.
The Dynastart is constantly in charge mode via the regulator/cutout, so you don't need the charge switch.
Top of pagePrevious messageNext messageBottom of page Link to this message

mike_sutcliffe
Member
Username: mike_sutcliffe

Post Number: 10
Registered: 07-2004
Posted on Monday, June 20, 2005 - 05:53 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Dragonrider, on my P66 with Siba Dynastart and coil ignition, I simply have a push / pull - off / on switch and a rubber insulated "press to start" button.

The dynastart continually charges whilst the engine is running which negates the requirement for a three way switch. When we wired up the boat we did not understand why you would switch off the charging whilst underway. Perhaps someone could explain!
Top of pagePrevious messageNext messageBottom of page Link to this message

dragonrider
New member
Username: dragonrider

Post Number: 3
Registered: 06-2005
Posted on Tuesday, June 21, 2005 - 06:23 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

I would like to thank the people who took the time and trouble to answer my query on 3 pos switch. Will now attempt to rewire new switches.(Watch my eyes light up) again thanks.Dave (ie Dragonrider)
Top of pagePrevious messageNext messageBottom of page Link to this message

Alex Stewart
Visitor
Posted on Friday, December 02, 2005 - 08:03 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

The reason for the 3-way switch is that the dyno (dynastart) draws a reletivly large amount of horsepower from what is a rather small motor. Switching off the charging enabled the motor to supply full horsepower to the propeller
Top of pagePrevious messageNext messageBottom of page Link to this message

Patrick O' Riordan
Member
Username: amy_ann

Post Number: 7
Registered: 04-2006
Posted on Tuesday, April 11, 2006 - 02:28 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Timmulvey,

Any chance you could email me a copy of that 3 page article on the dynastart.

Regards - Pat.
Top of pagePrevious messageNext messageBottom of page Link to this message

Tim Mulvey
Senior Member
Username: timmulvey

Post Number: 83
Registered: 05-2003


Posted on Friday, April 14, 2006 - 04:43 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Patrick - I'll do it tonight for you as well as for Peter (other posting)

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Automatically activate URLs in message
Action:

Administration Administration Log Out Log Out   Previous Page Previous Page Next Page Next Page

Home | Classifieds | History | Technical | Links | Store | About Us | Email
&copy 2005 OldMarineEngine.com, P.O. Box 188, Forest Dale, VT 05745-0188 • Phone: 802-247-4864 • All rights reserved.
   Marine Engine Seloc Repair Manual Lookup Tool

marine gas engine repair and restoration