Home | Classifieds | History | Technical | Links | Store | About Us | Email
Topics Topics Edit Profile Profile Help/Instructions Help Member List Register  
Search Last 1|3|7 Days Search Search Tree View Tree View  

P66

Old Marine Engine » Stuart Turner » P66 « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

John Allen
New member
Username: jayay

Post Number: 2
Registered: 08-2008
Posted on Sunday, February 01, 2009 - 07:38 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Can anyone help with the sourcing of a cylinder head gasket for my P66? With Fairways closure my previous source has gone.
Top of pagePrevious messageNext messageBottom of page Link to this message

David Myers
Senior Member
Username: dave_myers

Post Number: 62
Registered: 11-2006


Posted on Sunday, February 01, 2009 - 08:11 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

John,

Marlex Marine Technology Ltd based at Buckden Marina in Cambridgeshire have taken over all the Fairways stock and have spares available. URL is

www.stuartturnermarine.co.uk

Hope this helps

Dave in OZ
Top of pagePrevious messageNext messageBottom of page Link to this message

George Martin
Visitor
Posted on Sunday, February 01, 2009 - 02:42 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

I have just ordered P6 from here (made to measure from a photocopy). A bit more expensive than off the shelf, but reputed to be good quality.
www.gasketstogo.com
Top of pagePrevious messageNext messageBottom of page Link to this message

ken hillebrand
New member
Username: ken_hillebrand

Post Number: 2
Registered: 04-2008
Posted on Wednesday, February 04, 2009 - 06:40 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Many thanks to John Allen, George Martin, David Myers and Peter Ogborne for their comments re seals. I half suspected this may have been my problem but tried everything else in the hope that I would not have to completely dismantle the engine. I hope to take it out tomorrow and will dismantle it. Will keep you posted on my progress.
Thanks again
Ken
Top of pagePrevious messageNext messageBottom of page Link to this message

ken hillebrand
New member
Username: ken_hillebrand

Post Number: 3
Registered: 04-2008
Posted on Wednesday, February 18, 2009 - 04:26 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Have finally pulled the motor down (well not completely yet), I have found the flywheel collet broken into 2 pieces (looks like a very old break so it was probably put back together that way by the last person who worked on it prior to our purchase). Being in 2 pieces it made it very difficult to remove the front section of the motor as the peices were locking against one another. I am waiting for a reply from the Stuart Turner Spares place in UK as to whether they have one available and at what cost, I also have enquired locally about having one made in steel, and have been told it would cost AUST $120.

I have another problem in that I have found that I have tried both ways but it refuses to move either way, and I do not like the idea of perservering if I am turning it the wrong way. Any information on this would be appreciated. I also found that the holes immediately above the seals were blocked so this would be the reason for my problem.
Top of pagePrevious messageNext messageBottom of page Link to this message

Peter Ogborne
Senior Member
Username: peterogborne

Post Number: 291
Registered: 09-2002


Posted on Wednesday, February 18, 2009 - 06:08 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Ken ,I am sure I have a spare ,it would be from a P55 but they would be the same .If you are willing to pay the postage you can have it

Get in touch off list
Top of pagePrevious messageNext messageBottom of page Link to this message

ken hillebrand
Member
Username: ken_hillebrand

Post Number: 4
Registered: 04-2008
Posted on Wednesday, February 18, 2009 - 06:30 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Thanks Peter for the offer, can you send me your email address so I can be in touch with you, my email address is [email protected]

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Automatically activate URLs in message
Action:

Administration Administration Log Out Log Out   Previous Page Previous Page Next Page Next Page

Home | Classifieds | History | Technical | Links | Store | About Us | Email
&copy 2005 OldMarineEngine.com, P.O. Box 188, Forest Dale, VT 05745-0188 • Phone: 802-247-4864 • All rights reserved.
   Marine Engine Seloc Repair Manual Lookup Tool

marine gas engine repair and restoration