Home | Classifieds | History | Technical | Links | Store | About Us | Email
Topics Topics Edit Profile Profile Help/Instructions Help Member List Register  
Search Last 1|3|7 Days Search Search Tree View Tree View  

Blaxland Twin 10" Vee Pulley

Old Marine Engine » Blaxland » Blaxland Twin 10" Vee Pulley « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Michael Morris
New member
Username: m_morris

Post Number: 1
Registered: 07-2012
Posted on Thursday, July 19, 2012 - 07:43 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Wondering if anyone has a spare Vee Pulley for a Blaxland Twin that they would like to sell? It comes in two halves and is attached to the flywheel.
Top of pagePrevious messageNext messageBottom of page Link to this message

Andrew Munns
Senior Member
Username: johnoxley

Post Number: 63
Registered: 04-2010
Posted on Thursday, July 19, 2012 - 05:04 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Where are you? It would be sensible for me to transfer on some bits of a twin dynastart that I have.
Andy @ Baulkham Hills
Top of pagePrevious messageNext messageBottom of page Link to this message

Michael Morris
New member
Username: m_morris

Post Number: 2
Registered: 07-2012
Posted on Thursday, July 19, 2012 - 08:38 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Andy,
I am down on the Monrington Peninsula (Tootgarook)in Victoria. What bits do you have available?
Michael
Top of pagePrevious messageNext messageBottom of page Link to this message

Andrew Munns
Senior Member
Username: johnoxley

Post Number: 64
Registered: 04-2010
Posted on Saturday, July 21, 2012 - 07:56 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Have a twin crank with flywheel/starter and pulley at home - not perfect but good. There are some other bits on another site that I must visit and check. Will get back to you.

Andy
Top of pagePrevious messageNext messageBottom of page Link to this message

Michael Morris
New member
Username: m_morris

Post Number: 3
Registered: 07-2012
Posted on Sunday, July 22, 2012 - 02:37 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Thanks Andy,
sounds like you might have the bits and pieces I am after :-)
Look forward to finding out what else you might have.

Michael
Top of pagePrevious messageNext messageBottom of page Link to this message

Andrew Munns
Senior Member
Username: johnoxley

Post Number: 65
Registered: 04-2010
Posted on Monday, July 30, 2012 - 05:14 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Hi - the bits came off an engine in very rusted condition - usual rust wedging and crankcase badly rusted. There is a crankshaft with slightly damaged front end thread, a non-split pulley and I think a dynastart with pulley - Was there a regulator? The pulley is corroded and has some minor mechanical rim damage but is quite usable. The flywheel must be removed from the crankshaft to fit the pulley. This once took me 20 tons force from a 60 ton press. 12 tons did not do the job. Taper looks like a morse taper.
Top of pagePrevious messageNext messageBottom of page Link to this message

Michael Morris
Member
Username: m_morris

Post Number: 4
Registered: 07-2012
Posted on Tuesday, July 31, 2012 - 11:20 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Hi Andy, thanks for the info. Is the pully bolted onto the flywheel? Just wondering whether I would be able to cut the pulley into two halves in situ and remove rather than try and remove the flywheel from both your shaft and mine.
re the regulator - yes there was a standalone reg for the dynastart. Not to worry if you can't find it as I have a dynastart and reg I was going to use.
How much were you looking at for the bits and pieces?
Top of pagePrevious messageNext messageBottom of page Link to this message

Michael Morris
Member
Username: m_morris

Post Number: 5
Registered: 07-2012
Posted on Thursday, August 02, 2012 - 01:49 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Andy,
also wondering if you have the support brackets and the clamps to fasten the dynastart to the engine?
Top of pagePrevious messageNext messageBottom of page Link to this message

Andrew Munns
Senior Member
Username: johnoxley

Post Number: 67
Registered: 04-2010
Posted on Sunday, August 12, 2012 - 04:33 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Hi Michael, Problem with pulley - grit blasted and found 2 radial cracks from outside at 90 deg. 1 to 3/8" mount hole and one to large hole. Also some surface corrosion as Aluminium pulley is sacrificial to cast iron flywheel. Dynastart looks OK. No brackets. Regulator dented and switch broken. If it were my pulley I'd remachine a Stenco Al pulley.
Top of pagePrevious messageNext messageBottom of page Link to this message

Michael Morris
Member
Username: m_morris

Post Number: 6
Registered: 07-2012
Posted on Sunday, September 02, 2012 - 05:01 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Andrew, thanks for chasing up for me.
At this stage, I might keep looking for an original pulley.

If anyone else there has a pulley that they would like to part with please let me know.

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Automatically activate URLs in message
Action:

Administration Administration Log Out Log Out   Previous Page Previous Page Next Page Next Page

Home | Classifieds | History | Technical | Links | Store | About Us | Email
&copy 2005 OldMarineEngine.com, P.O. Box 188, Forest Dale, VT 05745-0188 • Phone: 802-247-4864 • All rights reserved.
   Marine Engine Seloc Repair Manual Lookup Tool

marine gas engine repair and restoration