Home | Classifieds | History | Technical | Links | Store | About Us | Email
Topics Topics Edit Profile Profile Help/Instructions Help Member List Register  
Search Last 1|3|7 Days Search Search Tree View Tree View  

Dunn 2 cylinder progress

Old Marine Engine » Dunn » Dunn 2 cylinder progress « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Tom Stranko
Posted on Friday, October 10, 2003 - 08:02 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

I decided not to try to press-off the flywheel
but just do as much of the sandblasting this week
as I could. I found this green-blue color all over but I assume it was a little darker originally (the sand or beadblasting does tend to change and lighten paint before it's gone)
It looks like the atmospheric intake valve holder
units have to be unscrewed. I hope that is not a problem. I plan on a more "normal" factory looking paint job on this one. A little filler
for the pits & holes but no real sanding. I'm using the darker green Ford 1929-31 engine color.
Top of pagePrevious messageNext messageBottom of page Link to this message

Tom Stranko
Posted on Friday, October 10, 2003 - 08:03 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

dunn1
Top of pagePrevious messageNext messageBottom of page Link to this message

Tom Stranko
Posted on Friday, October 10, 2003 - 08:05 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

dunn2
Top of pagePrevious messageNext messageBottom of page Link to this message

richarddurgee
Posted on Friday, October 10, 2003 - 10:50 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Tom
The valve holders are threaded !


Dunn valve

The color you posted looks more blue to me ??
This is doug Kimballs Dunn single that was posted here.

Dunn ome

This is original paint on flywheel that Bill Rupka
posted here.Its sure seems that some sort of blue was Dunns original paint color, Does anyone have any more info as to Dunns original paint color??
Top of pagePrevious messageNext messageBottom of page Link to this message

richarddurgee
Posted on Friday, October 10, 2003 - 10:56 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Flywheel pic

Dunn flywheel
Top of pagePrevious messageNext messageBottom of page Link to this message

Tom Stranko
Posted on Friday, October 10, 2003 - 12:25 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

The paint was a dark green before the sand started to remove it. It was like Model A Ford engine green. I could see the waves of green then blue as the paint was coming off. The paint on the cylinders was darker from grease and oil.
The flywheel was the best example. That picture you sent almost looks like you ran over to my mothers basement here in Pa. and unscrewed one housing for me!!
Top of pagePrevious messageNext messageBottom of page Link to this message

Tom Stranko
Posted on Saturday, March 06, 2004 - 02:07 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Picture of the mahagony wood cart I just finished for my 2 cyl Dunn. Is anyone familiar with aligning the cylinder plate with the crankshaft?
Thanks
Top of pagePrevious messageNext messageBottom of page Link to this message

Tom Stranko
Posted on Saturday, March 06, 2004 - 02:08 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

dunn
Top of pagePrevious messageNext messageBottom of page Link to this message

richarddurgee
Posted on Saturday, March 06, 2004 - 03:57 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Tom

I haven't assembled my Dunn II yet, what I intend to do with the plate is to completely assemble the eng then raise or lower the plate to get proper exhaust valve clearance, then with a machinists square, parallel the plate with top of crankcase maintaining valve clearance ??

That sure is a first class cart your Dunn gets to ride on !!
Top of pagePrevious messageNext messageBottom of page Link to this message

Tom Stranko
Posted on Saturday, March 06, 2004 - 07:12 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

I never gave the valve clearence a thought!! I was more concerned with the cylinder wall/piston rod being square with the crank. My engine had some damage and the distance of the plate to bed
was not unique all over. From what I measured at disassembly time, the height of the upper face of the nut under the plate measured 3.965", 3.985", 4.005". Some studs were broken and some nuts loose (did not measure them) From these measurements I assumed that I would be ok to start at 4".
Top of pagePrevious messageNext messageBottom of page Link to this message

Tom Stranko
Posted on Saturday, March 06, 2004 - 07:16 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

I forgot to mention the cart. It's nice to dress them up a little for the engine shows. I used just oak in the past but I got some big size mahogany a few years ago and the last 2 engines were done in that. It's not a fantastic job if you were to get down and look at it.
Top of pagePrevious messageNext messageBottom of page Link to this message

richarddurgee
Posted on Saturday, March 06, 2004 - 08:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

The exhaust valves in my DunnII have been refaced so many times over the yrs that the head diameter is a bit small for the seats, so making a pair of valves is probably the answer and they have very long stems. The stems should be identical in over all assembled length in relation to the cylinder plate. No provision for separate valve adjustment here,deck height will determine both valve clearances.


d
Top of pagePrevious messageNext messageBottom of page Link to this message

Tom Stranko
Posted on Saturday, March 20, 2004 - 03:53 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

I'm attaching a picture of my Dunn after getting the crankshaft and the camshaft alligned and the
shims cut etc. I have decided to use the blue loktite (Permatex actually) because there are no lock washers on the bolts and there are just slotted head pan screws holding the camshaft bearings down.
Tom
Top of pagePrevious messageNext messageBottom of page Link to this message

Tom Stranko
Posted on Saturday, March 20, 2004 - 03:54 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

dunn
Top of pagePrevious messageNext messageBottom of page Link to this message

Chuck Franklin
New member
Username: chuck

Post Number: 3
Registered: 05-2005
Posted on Sunday, November 26, 2006 - 03:17 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Moderator/Admin Only)

Can anyone send any info regarding Dunn engines, my=ine does not have a oil pan or crankcase sides. If anyone hase photo of these parts it would be a great help.

Thanks,

Chuck

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Automatically activate URLs in message
Action:

Administration Administration Log Out Log Out   Previous Page Previous Page Next Page Next Page

Home | Classifieds | History | Technical | Links | Store | About Us | Email
&copy 2005 OldMarineEngine.com, P.O. Box 188, Forest Dale, VT 05745-0188 • Phone: 802-247-4864 • All rights reserved.
   Marine Engine Seloc Repair Manual Lookup Tool

marine gas engine repair and restoration