Desperate need of a half a crankcase |
Author |
Message |
![Top of page](https://www.oldmarineengine.com/discus/icons/mark_top.gif) ![Previous message](https://www.oldmarineengine.com/discus/icons/mark_up.gif) ![Next message](https://www.oldmarineengine.com/discus/icons/mark_down.gif) ![Link to this message](https://www.oldmarineengine.com/discus/icons/tree_m.gif)
Jay Mac Visitor
| Posted on Saturday, September 08, 2012 - 09:19 am: |
|
I have recently purchased a Dispro D1 engine . She is in good condition except for one major flaw which I was aware of before the purchase The crankcase has two front halves of the crankcase bolted together so I am in desperate need of the back half of the crankcase. ( The water pump end) The engine would then be complete. An E1 would also work. Please let me know if anyone can help me and Thank you |
![Top of page](https://www.oldmarineengine.com/discus/icons/mark_top.gif) ![Previous message](https://www.oldmarineengine.com/discus/icons/mark_up.gif) ![Next message](https://www.oldmarineengine.com/discus/icons/mark_down.gif) ![Link to this message](https://www.oldmarineengine.com/discus/icons/tree_m.gif)
miro
Senior Member Username: miro
Post Number: 632 Registered: 11-2001
![](https://www.oldmarineengine.com/discus/messages/thumbnails/11047.jpg)
| Posted on Sunday, September 09, 2012 - 11:19 pm: |
|
Have you tried the Dippy Doctor? I can email you his contact info. Note the photo in my profile. Miro |
![Top of page](https://www.oldmarineengine.com/discus/icons/mark_top.gif) ![Previous message](https://www.oldmarineengine.com/discus/icons/mark_up.gif) ![Next message](https://www.oldmarineengine.com/discus/icons/mark_down.gif) ![Link to this message](https://www.oldmarineengine.com/discus/icons/tree_m.gif)
Jay Mac Visitor
| Posted on Wednesday, September 12, 2012 - 08:50 pm: |
|
Thanks Miro , but i have already contacted Paul- No luck |
![Top of page](https://www.oldmarineengine.com/discus/icons/mark_top.gif) ![Previous message](https://www.oldmarineengine.com/discus/icons/mark_up.gif) ![Next message](https://www.oldmarineengine.com/discus/icons/mark_down.gif) ![Link to this message](https://www.oldmarineengine.com/discus/icons/tree_m.gif)
mechman
Member Username: mechman
Post Number: 25 Registered: 10-2003
![](https://www.oldmarineengine.com/discus/messages/thumbnails/6130.jpg)
| Posted on Tuesday, September 25, 2012 - 08:56 am: |
|
Goodday I have a pair of bottom caseings I'm not sure what model they are from--The price would be $125.00 each--the back casting seems good--the front one will need some welding at the bolt holes connect to the cylinder--in any case sold "as is" Larry Healey [email protected]![dippy bottom castings](https://www.oldmarineengine.com/discus/messages/1/257551.jpg) ![both castings from top](https://www.oldmarineengine.com/discus/messages/1/257552.jpg) ![both from bottom](https://www.oldmarineengine.com/discus/messages/1/257553.jpg) |
|
|
|
![Marine Engine Seloc Repair Manual Lookup Tool](http://www.marineengine.com/manuals/seloc/lookup_190.gif)
![marine gas engine repair and restoration](http://www.marineengine.com/manuals/seloc/5000_small.jpg)
|