| Author |
Message |
    
John Werner
Visitor
| | Posted on Saturday, March 19, 2005 - 09:18 pm: | 
|
Muncie Gear works apparently built an oddball stern drive unit for only a couple of years. It is quite unusual. One of its distint features is that it turns 360 degrees, with no stops. It is nearly all bronze cast construction on the externals. I need info on this unit FAST if anyone can help me. The boat is going back in the water this coming week so the drive must be finished. Any help or info is greatly appreciated!! Thanks !! |
Trent Nabinger
Visitor
| | Posted on Sunday, September 11, 2005 - 09:26 pm: |
|
Hey John,
I don't have any info for you, but I did just lift a Muncie Gear Works motor out of the water. I was diving in about 15 feet of water looking for bottles and came acrost it. If you have any info on the unit I would greatly appreciate it if you could email me with it. emtnabinger@hotmail.com Thanks a ton, Trent Nabinger |
Tom Upton
Visitor
| | Posted on Sunday, April 02, 2006 - 10:09 pm: |
|
I have a Neptune Outboard motor, Model W C1, Serial # C 1542 RK. I need a propellar which is 6 " in diameter with a 1/2 " shaft. I also would like an engine manual. Can you suggest whom I should contact. |
William H. Davis
Visitor
| | Posted on Sunday, July 23, 2006 - 03:02 pm: |
|
I have a Johnson sea-horse TD 20. The Searial # is ,563937.Is this motor a 1946,or a 1947? Still runs real good. A friend of mine has a very small (1 hp?) MUNCIE boat motor.Model# is 1838.Searial # IS 6840.There is also a number on the carb. It is AC1A. Does anyone know what year motor it is?It does not run yet,but is not frozen up.Thank You for any info. |
greg kent
Visitor
| | Posted on Sunday, October 15, 2006 - 09:29 pm: |
|
I have an old Neptune outboard from the muncie gear works. The model is an 0B4 with serial 242. It has worked in the past 5 years. I got through the family from my dad and grandad. I would like to know what year it was made and is it worth anything. I can be reached at gm1kent@comcast.net |
Jeff Lowrie
Visitor
| | Posted on Sunday, March 18, 2007 - 09:39 pm: |
|
hi,i have a neptune outboard motor model #500,serial#k2726 cn it is baby blue in color and runs well. but need as much info as possible,like how to keep it tuned and to be able to work on it. PLEASE HELP,Thanks Jeff |
Valerio Coco
Visitor
| | Posted on Saturday, March 31, 2007 - 01:26 pm: |
|
I have a Neptune outboard engine model A1
and would like to make it run.
Does some one have operating instructions for this engine?
Unfortunatly the markings on the engine are no longer there.
Thank you
Valerio
javaco@bellsouth.net |
Bruce Hall
Senior Member
Username: bruce
Post Number: 137
Registered: 07-2002
| | Posted on Saturday, March 31, 2007 - 03:21 pm: |
|
The AOMCI.org site might help. Also; some time back;Tom Albertine,1336 N.183rd St.,Seattle Wa,98133 was listed as proctor of the AOMCI Neptune special interest group. Phone was 206-546-3026. Might want to do an Anywho.com google search to confirm this. |
Stacey Meekma
Visitor
| | Posted on Tuesday, May 22, 2007 - 04:21 pm: |
|
I work at a museum and we have an old Muncie Gear Company Outboard Motor Model No. 082 c Serial # 121 and I believe the year is 1981. Would anyone be able to tell me anything about this piece of equipment? |
Stacey Meekma
Visitor
| | Posted on Tuesday, May 22, 2007 - 04:35 pm: |
|
Actually I don't think it was 1981, that's probably when it was donated to the museum. |
dan brush
Visitor
| | Posted on Thursday, May 24, 2007 - 07:17 pm: |
|
i have a neptune outboard motor model # aa1 the seriel # is J254UU. if any one has info on this motor please contact me at sparkythefarmer@aol.com. i have started this motor once 3 years ago and would like to get it in good running ordor thank you. |
AaronHabegger
Visitor
| | Posted on Thursday, May 31, 2007 - 12:41 am: |
|
i have a neptune outboard motor model # is aa1 and serial # is G3817UR and im looking for any info on this motor that would help me get this motor running. Please contact me at firemen28270@yahoo.com if you have any info for me. thank you |
Aaron Habegger
Visitor
| | Posted on Sunday, June 10, 2007 - 12:57 am: |
|
i need to know what year this neptune motor i have was made in if anyone has this information i would greatly appericate it if some one could give me that information. model number AA1 serial number is G3817UR. also if anyone knows where i can get parts for it please contact me at firemen28270@yahoo.com Thank You |
David Peay
Visitor
| | Posted on Sunday, June 24, 2007 - 05:40 pm: |
|
I have uncovered a Neptune, Mighty Mite, model#WC1, Serial# D1034RR. Belonged to my Dad. I would like to know what year it was made.
Approximate value. I think I can get it running,but would love to get a manual or operating instructions..Any help will be appreciated. P.S. I live in Indianapolis, IN |
ray ravary
Visitor
| | Posted on Monday, October 01, 2007 - 06:05 pm: |
|
I have a Muncie gear works Neptune AA1A model, serial #g3670uq. I need to get a new prop for it, does any body have specs for the prop or info on where I could buy one? rravary@provide.net |
Scott Larson
Visitor
| | Posted on Saturday, December 29, 2007 - 10:08 am: |
|
I have a Neptune Motor Model AA1 Serial # C743 I cannot seem to find any info on it. It was my Grandfathers. Id bet my bottom dollar this thing fires right up in the spring. Anyone with any info on age of this motor and other information would be greatly appreciated |
mary esser
New member
Username: knowmezo
Post Number: 1
Registered: 01-2008
| | Posted on Sunday, January 13, 2008 - 10:21 am: |
|
I have a Neptune outboard motor serial no. F2972RK that has Muncie Gear Works Inc of Indiana. stamped on it. Can anyone tell me how old is it? And how do I go about getting parts to repair it? |
John Werner
Visitor
| | Posted on Monday, January 14, 2008 - 01:43 am: |
|
Well, time marches on. I haven't checked back for a few years. I garnered no info on the odd-ball Muncie stern drive unit but I did completely overhaul it and its attachments. It has been working for close to 3 years now so I guess I did okay. It appears that all of the generous responses concern the Muncie Gear Neptune outboards which are interesting little units but technically of little relationship to the outdrive I overhauled. Thanks |
Chuck Sarno
Visitor
| | Posted on Sunday, January 20, 2008 - 01:28 pm: |
|
I have a Neptune Motor Model No. B1, Serial No. B1378A, Muncie Gear Works. It also says Rephelon Co. Any information will be appreciated. |
Chuck Sarno
Visitor
| | Posted on Sunday, January 20, 2008 - 01:36 pm: |
|
I have a Neptune Motor Model No. B1, Serial No. B1378A, Muncie Gear Works. Can anyone tell me how old it is? It also says Rephelon Co. Any information will be helpful. |
Arthur Donaghy
Member
Username: wdboat
Post Number: 9
Registered: 08-2003
| | Posted on Sunday, January 20, 2008 - 06:55 pm: |
|
Chuck Sarno -
The records I have show the Neptune Model B1 to be a 1948 year model.
1.7hp 1 cylinder with a bore and stroke of 1.56" X 1.5".
R. E. Phelon was the maker of the magneto ignition system.
Hope this answers your question. |
Allan Stork
Visitor
| | Posted on Thursday, January 24, 2008 - 08:34 pm: |
|
Al Stork
My Father inlaw has a Neptune outboard (Muncie Indiana) Model # 500, Serial #1363 GK. Looking for year, hp, spark plug recommended, etc. Any information would be appreciated. Thanks |
jack geotech
Visitor
| | Posted on Tuesday, February 05, 2008 - 11:34 am: |
|
I have a Muncie Model 15 B1. Serial number H9275. If anyone has any info on motor, it would be greatly appreciated. Thanks |
Neal Rayborn
Visitor
| | Posted on Friday, February 08, 2008 - 07:22 pm: |
|
Looking for the 2-blade propeller for a WC1 Neptune Mighty Might. Any thoughts where I can find one??
Neal |
john gardner
Visitor
| | Posted on Saturday, May 03, 2008 - 05:19 pm: |
|
I just bought a bought a Muncie equiped boat that has ne chance of ever coming back to life. I believe it was a Cavellere by CrisCraft but it's hard to tell as the boat is so rotted. It has a 340 Buick V-8 and a Muncie outdrive with a nice two blade bronze prop. My outdrive does not spin 360 degrees like the other gentelman said his did but if anyone is interested in it cheap email me at johnsbmw@yahoo.com. I'm in Kansas City. I also have all the marine hardware for the engine if that interests anyone. |
John Smith
New member
Username: teksupman
Post Number: 1
Registered: 05-2008
| | Posted on Saturday, May 24, 2008 - 08:30 am: |
|
Hi, I too have a Neptune outboard. Model 17B1 Ser #D27366. Does anyone have any idea as to what year it may be? ANd if it is worth anything? email me at teksupman@hotmail.com
Thanks |
Kevin P. Kirsch
New member
Username: kkirsch
Post Number: 1
Registered: 05-2008
| | Posted on Tuesday, May 27, 2008 - 10:18 am: |
|
I have several old small neptunes. They all work well on 25 / 1 mixture. Never pull the head off otherwise it is all fair game to dissassemble. When running be sure to turn off the gas and run the carb bowl out prior to pulling out of the water. Also: make sure the screws are tight on the handle and all around the engine. If not they will end up in the water. Use grease in the lower unit. The gas tanks have a tendency to split open and leak. You can solve that problem by opening up the mounting holes for the tank and inserting some electical rubber pass throughs then remount as you would normally. |
John DePue
Visitor
| | Posted on Monday, June 23, 2008 - 04:43 pm: |
|
I have a Neptune outboard motor, Model 11 B 2, Serial # 43633 C2. I need to get the year, HP, and a possible source for the service manual. Any help would be appreciated. |
klinger726@yahoo.com
Visitor
| | Posted on Saturday, June 28, 2008 - 11:20 pm: |
|
I have a Neptune Model AA1, Serial # H4663U outboard motor(Muncie Gear Works). Unused since 1958. Need info to get working and curious to it's worth. Any info will be appreciated.} |
Roger DiRuscio
Senior Member
Username: solarrog
Post Number: 300
Registered: 03-2002
| | Posted on Saturday, June 28, 2008 - 11:35 pm: |
|
File and gap the points, clean the fuel tank, carburetor and fuel line, Try it. it may start
Value, go search ebay. Its the big show |
Mark Kelliher
New member
Username: kl7tq
Post Number: 1
Registered: 07-2008
| | Posted on Wednesday, July 16, 2008 - 04:53 pm: |
|
I own a Neptune WC1 Ser. #D1681RR and the Service Manual lists the :
A1 FROM 1955
AA1 1956
AA1-A 1957-1960
WC-1 1961-1969
The fuel mix is 16:1
I wish I could find a reed valve it runs at full trottle. it is a great little motor |
MD Beam with se9 sea eagle
Visitor
| | Posted on Sunday, August 03, 2008 - 04:40 am: |
|
man! I am going crazy.. i guess this little neptune aint so rare at all. seems everyone and their dog has one. i just wanted one to put on my raft - not one person has stated how much these
1.7 HP motors are worth. i do not want to pay More then I have to after all. LOL
the one I was looking to buy is the Mighty mite - in running condition. It would end up costing me between 100 and 120 after I pay shipping. do you think thats worth it?
anyone?  |
MD Beam with se9 sea eagle
Visitor
| | Posted on Sunday, August 03, 2008 - 04:46 am: |
|
here is a pic of the prospective motor i was seeking.    |
Roger DiRuscio
Senior Member
Username: solarrog
Post Number: 308
Registered: 03-2002
| | Posted on Sunday, August 03, 2008 - 10:54 am: |
|
I would not buy a motor with the skeg broken off
but the price you mention for a running motor is ok. the motor shown is a parts motor because of the broken skeg, These were cheap department store motors, and millions of them sold. They are always on the internet. Wait till a good one turns up |
John Vonada
New member
Username: johnalan
Post Number: 1
Registered: 09-2008
| | Posted on Saturday, September 06, 2008 - 11:26 am: |
|
I have a like new Muncie Gear Works Flexidrive 500 IO bolted to a hopped up 1949 Meryury auto engine and installed in a Glen L Home built boat. It was run for a couple of hours in 1969 and then put in storage where it remains today. I need to find a source of parts (rubber bellows and seale) or a buyer. Any help will ge greatly appreciated. |
samstanley
Visitor
| | Posted on Monday, November 03, 2008 - 07:16 pm: |
|
hello i have just been handed a unique animal,neptune by muncie gear comp., would like some help finding out what ive got here? mod#ob64a ser#46 or9h 2095or 2065,its in pretty good shape looking for year and any other info,thanks sam |
Adam Rice
New member
Username: pappabig10
Post Number: 1
Registered: 03-2009
| | Posted on Sunday, March 29, 2009 - 08:36 pm: |
|
My Uncle Got a Neptune Mighty Mite Model WC1 With a Serial # of E-3058 PA out of a trade We were wondering what year it was made and if it would be big enough to work on a 16' pontoon boat. any info would be greatly appreciated. |
Kevin P. Kirsch
New member
Username: kkirsch
Post Number: 2
Registered: 05-2008
| | Posted on Monday, March 30, 2009 - 08:02 am: |
|
Neptune Mighty-Mite, Model#WC1, 1.7 HP**Weighs 17 lbs.** manufactured in 1945-1947 by Muncie Gear Works in Muncie. It will push that boat but I would not get in a high wind with it. That motor is more for canoes and small boats (under 10 ft)long. You load the bottom with marine bearing grease and would be a good idea to put rubber or nylon washers on the gas tank mounts to ease vibrations to the tank. That motor tends to crack gas tanks. Every time you run it be sure to close the fuel valve and run the bowl out of gas then you will never have a problem with it. A good motor for your pontoon would be a 5 or 7.5 if you don't need to go fast. May I suggest a Scott 1-16 shift which is a 5 and has forward and reverse along with an intregral gas tank. |
william theodore
New member
Username: williamtheodore
Post Number: 1
Registered: 04-2009
| | Posted on Saturday, April 04, 2009 - 11:57 pm: |
|
I have a neptune wc1 which has 50 lbs of compression. Does anyone know what it should be.? |
Adam Rice
New member
Username: pappabig10
Post Number: 2
Registered: 03-2009
| | Posted on Tuesday, April 07, 2009 - 02:09 pm: |
|
We would also like to know bout the points and condensers in the mighty mite. the motor ain't gettin no fire at all |
SueGalde
Visitor
| | Posted on Tuesday, May 05, 2009 - 05:08 pm: |
|
My dad has the following:
MUNCIE GEAR COMPANY
MODEL #OB64A
SERIAL #A7 2258 X
Does anyone know anything about this "Engine Lubrication"? |
Ron Demarais
Visitor
| | Posted on Monday, May 18, 2009 - 06:30 pm: |
|
I've got one of these little motors in my barn.
Model No. AA1A
Serial No. B985U0
Looks like it may be fun to get running again! |
Joe Canavan
Visitor
| | Posted on Tuesday, May 26, 2009 - 05:50 pm: |
|
I havent seen any model numbers like mine? maybe its a misprint on the engine, but its A A1(Upside down A)A so if the third A wasnt upside down it would be A A1AA. Any ideas? |
jeff shain
Visitor
| | Posted on Sunday, June 14, 2009 - 11:24 pm: |
|
Hello, i just found a operating and instructions and repair parts catalog, owners handbook and service directory for moded A1 and B1, I opened the envelope (which had never been opened, but does say information for all neptune motors |
Simon P
Visitor
| | Posted on Wednesday, August 12, 2009 - 01:30 pm: |
|
Here are the parts catalogs for the Mighty mite
http://penn.itgo.com/images/MightyMite/mighty-mite-parts.html
and this guy bought the old factory inventory (new old stock) |
james kamprath
Visitor
| | Posted on Sunday, September 27, 2009 - 08:28 pm: |
|
i have a montgomery wards 15hp having trouble finding one small part for the lower end (impeller inside waterpump) do you know where i can find that part? |
luv2raceit
Visitor
| | Posted on Friday, October 30, 2009 - 12:49 pm: |
|
AA1A NEPTUNE FOR SALE,GREAT SHAPE bobmphd@aol.com |
luv2raceit
Visitor
| | Posted on Friday, October 30, 2009 - 12:54 pm: |
|
Clinton Motors outboard engine, two stroke is--( AIR COOLED )-- 5 hp.Sportfisher engine.aprox 15 hrs run time. has been stored for years inside.Has some scuffs from moving but runs very good. they were sold by western auto as Larson air cooled outboards. 175.00 obo.  |
Roger DiRuscio
Senior Member
Username: solarrog
Post Number: 383
Registered: 03-2002
| | Posted on Friday, October 30, 2009 - 01:42 pm: |
|
http://www.marineengine.com/cgi-bin/suite/classifieds/classifieds.cgi?request=di splay_sub&category_id=105&website=default&session=4aeb2429081d0903 <br>
try the classified section
these generally do not bring much money, but give it your best shot
 |
