| Author |
Message |
    
madmec03
New member
Username: madmec03
Post Number: 1
Registered: 06-2007
| | Posted on Monday, June 18, 2007 - 06:29 pm: | 
|
I have just bought an old boat with a Johnson/Evinrude 85 HP motor that needs some work. I need to know the year of this motor. The model # is 85ETLB775 The serial # is J4766638. Can any one help?
Thanks, Russell |
andrew
Moderator
Username: andrew
Post Number: 883
Registered: 11-2001
| | Posted on Monday, June 18, 2007 - 06:43 pm: |
|
Russell,
It is probably 85ETLR77S not 85ETLB775
That is a 1977. See this link for manuals.
Parts can be found here.
You can ask questions on the board at MarineEngine.com in the Johnson/Evinrude category. |
wgatormon
New member
Username: wgatormon
Post Number: 1
Registered: 06-2007
| | Posted on Monday, June 18, 2007 - 08:32 pm: |
|
I just obtained an old Evinrude outboard. It says on it whispering power aquasonis fleet twin 25.The only numbers I can find are as follows:7518-22380 no letters can anyone tell me the year and fuel mixture for this motor? Thanks Walter |
madmec03
New member
Username: madmec03
Post Number: 2
Registered: 06-2007
| | Posted on Monday, June 18, 2007 - 09:27 pm: |
|
Andrew,
Thank You it is 85ETLR77S It is worn a bit and couldn't see it well. Thanks for the help.
Russell |
fluvial
New member
Username: fluvial
Post Number: 1
Registered: 06-2007
| | Posted on Tuesday, June 19, 2007 - 08:57 am: |
|
I just purchased an Evinrude Jr outboard model # EJRCDR and serial # B018092 and would like to know more about it. What year was this motor made and what is the horsepower? I think it was made in 1986 but when I check that model year I cannot find this motor. |
Ben HartLenn
Visitor
| | Posted on Friday, July 20, 2007 - 01:51 pm: |
|
Can anyone tell me the fuel:oil ratio for a 1993 Johnson 9.9 Model# CJ10RLETR Serial# G 0299 4037 ?!?!? |
galpin
New member
Username: galpin
Post Number: 1
Registered: 07-2007
| | Posted on Tuesday, July 31, 2007 - 10:16 am: |
|
Does anyone have an instruction manual for a Evinrude EJRCDR Junior, 1986 1.2 hp? Specifically, I want to find out the best way of tweaking the air and fuel mixture dials and the throttle lever. You can send me a message at galpin@sympatico.ca and a scanned copy of the manual would also be great. |
empaynejr
Visitor
| | Posted on Wednesday, July 16, 2008 - 12:36 am: |
|
I have a 1979 Johnson 6HP, model# 6RL79E, that I use on a 22' sail boat.
I can get it to run just above idle, but when I open the throttle more it just stalls. Any suggestions? |
mike s.
Visitor
| | Posted on Monday, February 02, 2009 - 08:37 pm: |
|
i have johnson or evinrude motor ,twin ,light blue faded name i think it says johnson mod#OD-10 serial#822707 does anyone know hw to tell |
galpin
New member
Username: galpin
Post Number: 2
Registered: 07-2007
| | Posted on Monday, February 02, 2009 - 09:19 pm: |
|
Try this web site. It has manuals for lots of engines: Put Evinrude in the product box and go from there. 1986 1.2hp etc. Carburetor Crankshaft&Piston etc.etc.With each of the systems are the part number plus a diagram of the system. http://epc.brp.com/login.aspx?Return...ands=ej&lang=E |
JOHN SALVAGGIO
Visitor
| | Posted on Thursday, April 02, 2009 - 02:49 pm: |
|
I HAVE AN 1977 JOHNSON 85HP MODEL 85ETLR77S AND I WAS WONDERING IF THERE IS A SPOT TO PUT A PEE NOZZLE SO I KNOW IF THE WATER IS TRAVELING THOUGH THE MOTOR. ANY ADVICE WOULD HELP |
dshands
New member
Username: dshands
Post Number: 1
Registered: 05-2009
| | Posted on Friday, May 08, 2009 - 03:30 pm: |
|
I have a 1977 Johnson (Javlin) motor model # 85ETLR77S on my Thompson boat. The problem I have is that sometimes it starts and runs great. Then there are times that it rolls over, but will not fire up it is hit or miss if it'll start. I have a new battery on it. Any suggestions or help would be appreciated. |
solarrog
Senior Member
Username: solarrog
Post Number: 356
Registered: 03-2002
| | Posted on Friday, May 08, 2009 - 03:43 pm: |
|
Sounds like its time for an ignition tune up
generally fuel problems are not intermitant |
ernie
Senior Member
Username: ernie
Post Number: 972
Registered: 01-2002
| | Posted on Friday, May 08, 2009 - 05:16 pm: |
|
It should be new enough to have good ignition coils. However it is worth a look. Remove the tin cover in the middle of the flywheel and make sure the coils are not cracked. If they are it will be very obvious and they need to be replaced. If you need replacement coils they are available from www.marineengine.com
Hope this helps
Ernie |
jb_castagnos
Senior Member
Username: jb_castagnos
Post Number: 451
Registered: 07-2002
| | Posted on Friday, May 08, 2009 - 06:51 pm: |
|
I think this Javelin is a V4, if so it probably has 4 coils, I would look at the stator or module. The stator can be checked for a/c voltage, I don't know the values, but they were a problem area. |
dshands
New member
Username: dshands
Post Number: 2
Registered: 05-2009
| | Posted on Saturday, May 09, 2009 - 05:04 pm: |
|
I'd like to say thankyou to all that replied so quickly to my post. It sounds like my problem will be relatively easy to check and fix. I will check those items soon. It sounds like I'll be boating in no time at all. |
Bette
Visitor
| | Posted on Saturday, June 06, 2009 - 12:09 pm: |
|
I just purchased an Evinrude Junior on Ebay - Belgium #B0106869 - JRCDR. Have not received it yet but it was advertised to "run great" and will be used with a fiberglas rowing boat. What should I know about this motor - year of mfg? reputation for reliability, maintenace schedule, etc? Many thanks. |
dshands
New member
Username: dshands
Post Number: 3
Registered: 05-2009
| | Posted on Saturday, July 11, 2009 - 05:52 pm: |
|
I have a 1977 Johnson outboard motor model # 85ETLR77S on my Thompson boat. The problem I have is that when I put the boat in reverse, it's like it dosen't catch. Eventually it does go into gear, but not after it makes a noise like something is missing. I have no issues with the forward gear. I've been told that my linkage needs to be adjusted. Two years ago I had new throttle cables installed. How hard is it to properly adjust the linkage if this is the problem. This problem just started. |
joshkuchinka
Visitor
| | Posted on Thursday, October 29, 2009 - 09:11 am: |
|
I replaced my inpeller on my 73 25 hp evinrude. Put it all back together, and no forward. only reverse and neutral. I messed with the linkage through the access on the side of the motor, but nothing what should I do next?? |
